Power Supply Current Measure IP

Power Supply Current Measure IP is an algorithm IP to measure power supply current.

By using Power Supply Current Measure IP, the following electrical characteristics for target devices can be measured and evaluated easily.

  • Static power supply current
  • Dynamic power supply current

In addition, by using Multipoint Measurement Plugin, the following electrical characteristics for target devices can be measured and evaluated easily.

  • IDDQ test
  • Maximum power supply current
  • Minimum power supply current
  • average power supply current
  • Variability for power supply current (3σ)

Features

This IP has the following functions.

  • Can measure the power supply current for the pin connected to the following channels.

    • Power Supply
    • RVS
    • ATES UTILITY Power Supply 6V 4A
      It is a channel of UTILITY BOX manufactured by ATE Service Corporation. It can be used when connecting to UTILITY BOX.
  • Can measure the power supply current for the specific operating state by executing pattern. For the details, refer to Pattern Execution and Measurement.

  • Can measure by opening the pin out relay of the I/O pin. It is possible to reduce the influence of the leakage current of the measurement system. For the details, refer to Change Operating State for I/O pins.

  • Can measure by applying VIH/VIL voltage to the device pins. For the details, refer to Change Operating State for I/O pins.

  • Can measure by changing the measurement range. For the details, refer to Change Measurement Range for Power Supply.

  • Measurement values and judgement results can be stored to variables by interpose processing. For the details, refer to Interpose Processing.

  • Can judge the pattern execution result. For the details, refer to Judgement for Pattern Execution Results.

  • Execute the finalization pattern. For the details, refer to Execute Finalization Pattern.

  • Apply the arbitrary waveform synchronized with pattern by Arbitrary Waveform Applying Plugin.

  • Supply the power from external power supply instruments controlled by GPIB by External Power Supply Control Plugin.

  • Measure by multiple pattern execution condition in one test item (in the rest of this document referred to as “Multipoint Measurement Function”) by Multipoint Measurement Plugin. In addition, can judge statistical values at each measurement point. For the details, refer to Multipoint Measurement Plugin Reference Manual.

  • Execute the batch file at specified timing of the measurement sequence to algorithm IPs by Batch File Execution Plugin.

Add to Cart

Product GroupAlgorithm IP
CodePCXA01-M1028
Link
ManufacturerADVANTEST CORPORATION
Applicable Equipment
  • CX1000P CX1000_MCU
  • CX1000D CX1000_MCU
  • CX1000D S2-LINK CX1000_MCU
Multipoint Measurement Plugin

Shmoo Plot Tool

External Power Supply Control Plugin

Shmoo Algorithm

Arbitrary Waveform Applying Plugin

Generic Search IP

Batch File Execution Plugin

Revisions

Released atNumberDescription
January 25, 20212.06.10
  • Fixed an issue that the parameter of [(9) Execute Finalization Pattern] on [Measurement Setting] tab may not be displayed depending on the screen size.
October 06, 20202.06.00
  • Supported power supply current measurement with UTILITY BOX (ATES UTILITY Power Supply 6V 4A channel) manufactured by ATE Service Corporation.
May 29, 20202.05.00
August 28, 20192.04.00
  • Added the function to change the source voltage at the measurement.
  • Added the function to execute the finalization pattern.
  • Supported Batch File Execution Plugin.
  • Fixed an issue where changed values of [(2)Wait] and [(6)Wait] were not reflected correctly.
March 13, 20182.03.00
  • Added the function to output the comments and variable values to header of data log.
  • Fixed an issue that an error occurred at execution when [Acquisition Count] was the initial value without editing by using Multipoint Measurement Plugin.
  • Fixed an issue that an error occurred when executing the measurement after address specification was switched from label to variables in [Measurement Table] by using Multipoint Measurement Plugin.
  • Supported External Power Supply Control Plugin R1.02.01.
October 04, 20172.02.00
  • Added the following content to the reference manual.
    • Measurement sequence when measurement range is specified.
    • Comparison with measurement sequence of Rev1.02.01.
August 28, 20172.01.91
  • Fixed an issue that an error occurred when loading a work project generated by preceding revision (i.e. earlier than Rev2.00.00) and then execute Shmoo Plot Tool (PCXT01-M6001) or Shmoo Algorithm(PCXT01-M6000).
  • Fixed an issue that an error occurred when using External Power Supply Control Plugin(PCXA01-M1039).
May 18, 20172.01.00
  • Fixed an issue that the judgment items selected in [Judge item(s)] on [Multipoint Measurement Setting] tab is available when [Enable Multipoint Measurement Function] on [Multipoint Measurement Setting] is disabled.
  • Fixed the error message displayed when [Measure Pin] of [Target Pin Table] in [Measurement Setting] tab specifies same pin name on multiple lines.
  • Fixed an issue when displaying [Measurement Setting] tab after loading a work project, the value specified for [(7-5) Wait] is forced to change to default value.
  • Added a condition confirmation to [(4) Set VIH Level] and [(5) Set VIL Level] on [Measurement Setting] tab.
March 01, 20172.00.00
April 21, 20151.02.00
  • The product name is changed to Power Supply Current Measure IP.
  • Can measure the frequency with a loop execution of MAIN pattern.
  • Can be measured the frequency without changing the pattern program when using loop function.
  • Address range of loop execution of pattern that is used in frequency measurement is unrestricted.
  • If contract with old product name is change procedure of contract associated with the product name change is not required.
February 02, 20151.01.00
  • It is possible to measure the power supply current by using the RVS(Reference Voltage Supply).
  • Support IP Manager
  • Change log output format
July 09, 20141.00.00

First edition Product NameF Power Supply Current Measurement