January 20, 2022 | 2.45.00 |
|
April 01, 2021 | 2.44.00 |
-
Fixed issue
-
Memory leak at startup Due to a memory leak at startup, a lot of memory was consumed when it was started and closed repeatedly.
|
August 28, 2020 | 2.43.01 |
- Fixed issues
- Initialization and termination processes were not performed when executing measurement under the any point of the Shmoo result.
- Behavior after improvement
In the condition above, initialization and termination processes is performed.
- Revisions in which this phenomenon occurs
Rev 2.22.00 - Rev 2.43.00
- When the Shmoo Plot Tool could start due to an error of the measurement conditions, an unnecessary error message was displayed in the message display area when the variable definitions were changed.
- Behavior after improvement
An unnecessary error message is not displayed.
- Revisions in which this phenomenon occurs
Rev 1.00.00 - Rev 2.43.00
|
August 07, 2020 | 2.43.00 |
-
Addition of functions
- Supported for UTILITY BOX made by ATE Service(Supported only in Japan).
|
February 03, 2020 | 2.41.01 |
-
Fixed issues
- The measurement results were not displayed when re-executing the measurement at any point of the Shmoo result.
[Behavior after improvement] In the condition above, the measurement results are displayed. [Revisions in which this phenomenon occurs] Rev 2.41.00
|
January 16, 2020 | 2.41.00 |
- Supported Initial and Final settings of pre-processing and post-processing items.
- Added the function to stop analysis processing when the results of pre-processing and post-processing items are Fail or Error.
- Added the function to select the measurement items for acquiring Shmoo results.
- Supported the function to output the data log of the measurement items during acquisition of Shmoo data.
- Improved to re-evaluate parameter variables before execution.
|
May 09, 2016 | 2.25.00 |
-
Fixed issues
-
When executing the Shmoo again soon after stopping the Shmoo execution, the Shmoo data could not be obtained correctly.
- Behavior after improvement
- In the condition above, Shmoo can be obtained correctly.
- Revisions in which this phenomenon occurs
- Rev 1.00.00 to Rev 2.24.00
-
After the Shmoo Plot was started, an error occurred when the measurement item with the changed signal conditions was executed.
- Behavior after improvement
- In the condition above, the measurement item is executed properly.
- Revisions in which this phenomenon occurs
- Rev 2.24.00
-
The Shmoo results were cleared after executing the measurement item.
- Behavior after improvement
- In the condition above, the Shmoo results are not cleared.
- Revisions in which this phenomenon occurs
- Rev 2.24.00
|
March 18, 2016 | 2.24.00 |
The variables can be specified for X-axis and Y-axis parameters.
|
September 30, 2015 | 2.23.00 |
- Setting the value of any point of Shmoo result to the measurement conditions
- This feature can be used for using the value of any point of Shmoo result in other analysis tools
|
July 22, 2015 | 2.22.03 |
Not get the Shmoo to be selected FixLevel to the parameters of the Shmoo
When the FixLevel signal condition window , was chosen as Shmoo parameter, I could not get the Shmoo unable to set the Shmoo axis conditions .
[Behavior after improvement]
In the condition above, Shmoo can get.
[Revisions in which this phenomenon occurs]
Rev 2.22.00
|
June 08, 2015 | 2.22.00 |
- Suppoting interpose processing in Expert Mode
- Interpose processing in Expert Mode was supported.
- Executing measurement under the any point of the Shmoo result
- The measurement can be executed under the any point of the Shmoo result. And,the measurement condition can be shown after measurement.
- Applying the modified measurement conditions
- If the measurement conditions are changed on the CloudTesting(TM) Lab, the changed conditions are applied immediately.
- The error occured on measurement conditions when the particular tracking is specified
- If the tracking for the period is specified, the error occured on measurement conditions and the result was incorrect.
- [Behavior after improvement]
- In the condition above, the measurement result is correct.
- [Revisions in which this phenomenon occurs]
- Rev 1.00.00 - Rev 2.12.00
- The measurement conditions on the CloudTesting(TM) Lab are changed unexpectedly
- If the Pattern Viewer was linked without obtaining Shmoo Plot, the measurement conditions of the selected point were set to the CloudTesting (TM) Lab.
- [Behavior after improvement]
- In the condition above, the measurement conditions are not changed.
- [Revisions in which this phenomenon occurs]
- Rev 1.00.00 ` Rev 2.12.00
- Warning message was shown incorrectly
- When the Y axis parameter was specified, the following warning message was shown incorrectly while obtaining Shmoo Plot.
- [Warning!! The measurement condition of this pin(< pin name>) is overwritten.]
- [Behavior after improvement]
- In the condition above,the warning message is not shown incorrectly.
- [Revisions in which this phenomenon occurs]
- Rev 1.00.00 - Rev 2.12.00
- Lack of the description for the Shmoo log
- The description of [Not Executed] was missing in the Shmoo log.
- [Behavior after improvement]
- The description of [Not Executed] is shown.
- [Revisions in which this phenomenon occurs]
- Rev 1.00.00 ` Rev 2.12.00
|
February 02, 2015 | 2.12.00 |
- General Required Java version was changed to 8
- Now CloudTesting(TM) Lab requires Java8. Please download and install Java Runtime Environment 8 from Oracle site.
- IP Manager
- Automatic installation and authentication for the IPs that you have purchased.
|
August 29, 2014 | 2.11.00 |
- Improvement tracking
- If the measurement condition of two or more pins was defined by one, Shmoo can not be acquired while tracking any parameter.
- [Operation after improvement]
- Shmoo can be acquired while tracking any parameter.
- [Revisions in which this phenomenon occurs]
- Rev 1.02.00 to Rev 2.10.00
|
May 30, 2014 | 2.10.00 |
- Add trackable parameter
- Shmoo can now be acquired while tracking following parameters.
- Termination voltage
- Load Threshold
|
November 01, 2013 | 1.02.00 |
- Support for tracking
- Shmoo can now be acquired while tracking any parameter.
|
January 24, 2013 | 1.01.00 |
This revision is released to only Japan.
|