Reason for revision
Addition of functions, Functional improvement
Addition of functions
General
Required Java version for CX50 was changed to 8
CloudTesting™ Lab for CX50 requires Java8. Please download and install Java Runtime Environment 8 from Oracle site.
- Target firmware
- CX50_GENERAL
IP Manager support CX50
The IPs for CX50 were supported.
- Target firmware
- CX50_GENERAL
The interpose algorithm relaxes its restriction
The interpose algorithm can store the measured data into the array variable when the size of the array variable is greater than the count of measured data.
- Target firmware
- CX1000_MCU, CX1000_MEMORY_TYPE_F
Setup and Execution
Improvement of the voltmeter and ammeter in the [Circuit] tab
The following functions were added to the voltmeter and ammeter in the [Circuit] tab. - [Difference Meter] panel was added. - X-axis of the meter mode(recoder) displays time. - Ranges of meter modes (Meter and Recorder) were unified.
- Target firmware
- CX50_GENERAL
Improve the function of repeating execution of the experiment item
The initialization and finalization are not performed in each execution.
The repeating execution can be paused.
- Target firmware
- CX50_GENERAL
Maintenance Program
Addition of function that check condition in Firmware installation.
Addition of function that check Windows Update being applied in Firmware installation .
- Target firmware
- CX50_GENERAL
Functional improvement
General
Improve the function of data log settings
The data log settings was sometimes not applied in the simple data log mode.
- Behavior after improvement
- The data log settings is applied properly.
- Phenomenon occurs revision
- Rev2.20.00
- Target firmware
- CX1000_MCU, CX1000_MEMORY_TYPE_F
Improvement of the unexpected hang-up
Hang-up sometimes occurred at the end of CloudTesting™ Lab or installation of firmware during CX50 operation.
- Behavior after improvement
- The hang-up does not occur.
- Phenomenon occurs revision
- Rev 2.00.00 to Rev 2.11.02
- Target firmware
- CX50_GENERAL
CT Command did not work even if you had purchased ‘OperationWindow for CX1000’
The following CT Command did not work even if you had purchased ‘OperationWindow for CX1000’. * CT_MeasureItemStart.bat * CT_MeasureItemStartNoWait.bat * CT_MeasureItemStop.bat * CT_MeasureItemGetErrorMessage.bat * CT_MeasureItemGetStatus.bat * CT_MeasureItemGetResult.bat * CT_MeasureItemSelect.bat * CT_MessageAreaSetLoggingMode.bat * CT_MessageAreaSetLoggingFileName.bat * CT_MessageAreaPrint.bat * CT_MessageAreaSetMaximumTextLength.bat * CT_MessageAreaClear.bat * CT_MessageAreaSave.bat * CT_WorkProjectOpen.bat * CT_WorkProjectShowIPInfo.bat * CT_VariableDefine.bat * CT_VariableSet.bat * CT_VariableGet.bat * CT_VariableExists.bat * CT_VariableGetArraySize.bat * CT_VariableShowInfo.bat * CT_HeaderSet.bat * CT_FooterSet.bat * CT_DataLogSet.bat
- Behavior after improvement
- In the condition above, they work properly.
- Phenomenon occurs revision
- Rev2.20.00
- Target firmware
- CX1000_MCU,CX1000_MEMORY_TYPE_F
Installer
CloudTesting™ Lab didn’t run automatically
CloudTesting™ Lab did not run automatically if some ‘Unknown device’ exist.
- Behavior after improvement
- CloudTesting™ Lab automatically runs properly.
- Phenomenon occurs revision
- Rev2.11.00 to Rev2.20.00
- Target firmware
- CX1000_MCU,CX1000_MEMORY_TYPE_F,CX50_GENERAL
IP Manager didn’t work propery at the environment where proxy was required
IP Manager didn’t download IPs at the environment where proxy was required to connect to the Internet.
- Behavior after improvement
- Any network communication is established through the proxies of Windows internet option setting.
- Target firmware
- CX1000_MCU, CX1000_MEMORY_TYPE_F
Improvement for the messages of IP Manager
Error messages and authentication screen were shown repeatedly if it didn’t connect to the Internet.
- Behavior after improvement
- The messages that were shown on non-internet connection were improved.
- Target firmware
- CX1000_MCU, CX1000_MEMORY_TYPE_F
Setup and Execution
After changing the [Resolution], measurement results were not correct.
In case of executing a measurement after changing the [Resolution] in the signal condition window, measurement results were not correct.
- Operation after improvement
- In the condition above, the measurement execution works properly.
- Revisions in which this phenomenon occurs
- Rev 2.20.00
- Relevant firmware
- CX1000_MEMORY_TYPE_F