CloudTesting™ Lab 2.11.00

Reason for revision

Addition of functions, Functional improvement

Enhanced functions

Installer

Function to update the firmware was enhanced.

The firmware can be updated in the process of the CloudTesting™ Lab installation.

Relevant firmware
All firmwares

Setup and Execution

Function to select timing resolution

[1.25n], [1n], [938p] or [834p] can be selected for the timing resolution in the signal condition window. As a result, 3.75ns can be set for [Period] as minimum.

Relevant firmware
CX1000_MEMORY_TYPE_F

Signal condition window was enhanced.

The following functions were added to signal condition window. - Cyclic Redundancy Check(CRC) - Relative Card Address(RCA) - Source Sync - Driver Enable Signal for [In] pin - Judge Enable Signal for [Out] pin - Invert of Pin Data Select

Relevant firmware
CX1000_MEMORY_TYPE_F

Bad Block Memory was supported.

The fail capture condition window has capability for setting Bad Block Memory.

Relevant firmware
CX1000_MEMORY_TYPE_F

Function to set source range in power supply condition window was supported.

Source range can be set in power supply condition window.

Relevant firmware
CX1000_MCU, CX1000_MEMORY_TYPE_F

Maintenace program

Function to select a digital multimeter was supported.

The digital multimeter for the calibration is selectable in [Maintenance Program Settings] dialog.

Relevant firmware
All firmwares

Some SelfCheck items was supported.

The following SelfCheck items are supported. 30294 ALPG PC JFFI & MATCH PINSEL FUNC CHECK 30295 ALPG PC MATCH COMBINATION CHECK 1 30296 ALPG PC MATCH COMBINATION CHECK 2 30302 ALPG PC JMZ INST CHECK (2WAY) 30303 ALPG PC JFFI & MATCH PINSEL FUNC CHECK (2WAY) 30304 ALPG PC MATCH COMBINATION CHECK 1 (2WAY) 30305 ALPG PC MATCH COMBINATION CHECK 2 (2WAY) 30319 ALPG CONT FAIL & WAIT INT CHECK 30387 ALPG DFM STORE CHECK 18 (ETC) 30399 ALPG DFM STORE CHECK (ETC - 2WAY) 52010 DCL DR/CP FUNCTION & AC CHECK 52020 DCL DR/DIFF CP FUNCTION & AC CHECK 70122 FT SC SOURCE SYNC MODE FUNCTION CHECK 11 (2WAY) 70126 FT SC SOURCE SYNC MODE FUNCTION CHECK 15 (1WAY)

Relevant firmware
CX1000_MEMORY_TYPE_F

Firmware

Speedup of Installing Firmware

Installing Firmware was shortened for about 10 minutes.

Relevant firmware
CX1000_MCU

Other

Function to save work-project was enhanced.

When saving the project that contains the measurement algorithms that are not installed, the information for them is no longer lost.

Relevant firmware
CX1000_MCU, CX1000_MEMORY_TYPE_F

The timing is calibrated when the CTS FUNC cable(1m) is used.

Even when you use the CTS FUNC cable(1m), the timing is calibrated.

Relevant firmware
CX1000_MCU, CX1000_MEMORY_TYPE_F

Improvement items

Firmware

Failure of the Fixed delay cycle match(FLG/JMZ/JFFI) instruction

Match2 to Match4 don’t work correctly when the Fixed delay cycle match instruction is used in pattern programs.

Behavior after improvement
Match2 to Match4 work correctly.
Revisions in which this phenomenon occurs
Rev2.10.00
Relevant firmware
CX1000_MEMORY_TYPE_F

Failure when some Match instructions are used

The function does not work correctly when the Fixed delay cycle match instruction is used immediately after the Fixed delay match instruction in pattern programs.

Behavior after improvement
The function works correctly.
Revisions in which this phenomenon occurs
Rev2.10.00
Relevant firmware
CX1000_MEMORY_TYPE_F